|
沸騰干燥機典型的系統雙層沸騰干燥機/冷卻器Kason（凱勝）的雙層，圓形流化床處理器顯著降低資本成本，能耗和占地空間每磅產品的干燥或冷卻。的上部甲板的加入使得使用，否則將被耗盡后的下層通過加熱或冷卻的空氣，并且需要在尺寸或不平衡重量電機或風機的能源消耗幾乎沒有增加，幾乎加倍容量和幾乎沒有增加經營成本或建筑面積的效率。與矩形流化床處理器，需要重軌的建設，經受住不斷振動，循環流化床處理器本質上是剛性的，從而使材料的建設是衡量和振動電機精簡。也消除了相關部件，如多個風口和出風口及其相關的管道 - 圓形裝置，只需要一個每個。其結果是一個單元的顯著較輕的重量和較高的工作效率，與較低的資本成本和更小的體積，相當于床范圍和容量比矩形流化床處理器。減少材料，焊縫，以及相關的勞動降低制造成本，特別是在單位完成FDA，USDA，BISSC或3-A標準。減少焊縫，一個快速斷開住房，而沒有內部橫梁，循環流化床處理器減少清洗時間顯著。正在申請專利的雙層流化床系列處理器，直徑從48“至84”（1220毫米2135毫米），四種型號的滿足中，大批量的生產要求�？膳渲脼檫B續的干燥，冷卻或保濕的應用程序。標準裝備：控制入口溫度，空氣流速，床的深度和停留時間，快速斷開夾具，快速，徹底的清潔，流化床空氣分配器的選擇高扭矩馬達驅動雙延伸軸和偏心重量調整系統，以優化特定材料的振動運動連續或間歇操作304不銹鋼接觸面可調式溢流堰控制層的深度選裝配置：3A，F(xiàn)DA，和BISSC標準建設就地清潔噴頭防爆電氣惡劣環境應用316或更高等級的不銹鋼材料接觸面Vibro-BedTM TYPICAL SYSTEMSDouble-Deck Fluid Bed Dryer/CoolerKason's Double-Deck, Circular Vibratory Fluid Bed Processor significantly reduces capital cost, energy usage and floor space per pound of product being dried or cooled.The addition of an upper deck makes use of heated or cooled air that would otherwise be exhausted after passing through the lower deck, and requires little to no increase in the size or energy consumption of imbalanced-weight motors or blower fans, nearly doubling capacity and efficiency with little to no increase in operating cost or floor space.Unlike rectangular fluid bed processors that require heavy-gauge construction to withstand constant vibration, circular fluid bed processors are inherently rigid, allowing materials of construction to be down-gauged and vibratory motors to bedownsized. Associated components are also eliminated, such as multiple air inlets and outlets and their associated ducting — the circular unit requiring only one of each. The result is a unit of significantly lighter weight and higher operating efficiency, with lower capital cost and a smaller footprint, than rectangular fluid bed processors of equivalent bed area and capacity.Reductions in material, weld seams, and associated labor decrease fabrication cost, particularly when units are finished to FDA, USDA, BISSC or 3-A standards.With reduced weld seams, a quick-disconnect housing, and no internal cross-members, circular fluid bed processors cut cleaning time dramatically.Four models of the patent pending, double-deck fluid bed processor range in diameter from 48" to 84" (1220mm to 2135mm), satisfying medium- to high-volume production requirements. All are available configured for continuous drying, cooling or moisturizing applications.Standard Equipment:Controls for inlet temperature, air velocity, bed depth, and retention timeQuick-disconnect clamps for fast, thorough cleaningChoice of fluid bed air distributorHigh Torque motor drive with double extension shaft and eccentric weight adjustment system to optimize vibratory motion for specific materialsContinuous or batch operation304 Stainless steel contact surfacesAdjustable weir to control bed depthOptional Equipment:Construction to 3A, FDA, and BISSC standardsClean-in-place spray headsExplosion proof electricals for hazardous applications316 or higher grade stainless steel material contact surfaces 1 ．超細氣流粉碎是一種新穎獨特的超細粉碎技術。與傳統的機械法粉碎相比，采用超細氣流粉碎技術的較大特征是：粉碎產品的粒徑可達微米級甚至亞微米級；粒度分布范圍狹窄；粉碎產品純正，不因磨損而受到金屬或非金屬雜質污染；由于高壓氣體工質通過噴嘴產生的焦耳—湯姆遜效應和粉碎時間極短，尤為適合熱敏性和低熔 混合機的發展是比較快的，它的發展給人很大的幫助，既減輕了勞動力的付出，也為擁有者帶來了更大的產量，從而獲得更多的經濟效益，當然混合機的種類也比較多，在各個行業都有它的身影，發揮著自己的能力，體現這它的價值所在，既然它為人們作出了極大的貢獻，那它的工作原理是什么，我們今天就拿旋錐形混合機的工確定了烘箱的有效長度，車速，噴孔的形式，噴孔的空氣速度及空氣溫度后，就要對烘箱進行熱平衡計算。其計算方法分為烘箱在正常生產時所需的熱量及烘箱在正常升溫時所需的熱量，對兩者進行比較，取其^大者為所需的熱量。 熱風循環烘箱在正常生產時所需的熱量由以下各部分碳化硅（SiC）是一種硅和碳的化學配方復合SiC。它是自然界中極為罕見的礦物碳硅石。碳化硅粉末已批量生產從1893 用作磨料。碳化硅顆�？梢酝ㄟ^燒結形成很硬的陶瓷廣泛應用于需要高耐力 應用結合在一起，如汽車的剎車，汽車離合器 和陶瓷防彈衣防彈。電子應用碳化硅為發光二極管（LED）在早期收音機首次展示一個成功的工廠依賴于關鍵流程的整合單位正確選擇輔助設備和正確的設施的設計�？煽啃裕僮鞣奖�，結構堅固，性能和優質的客戶服務都是商標。我們提供一個非常廣泛的不同的選項和附加設備�！ ∥覀兊姆序v干燥機采取的干燥室的設計，制造和安裝的所有工作，客戶服務將幫助建立了設備和培訓員工。我們提供擔保的設備，并
|
